Installation Instructions

SOLID WOOD FLOOR 3/4 “(19mm)

 

GENERAL INFORMATION:

 

Responsibilities of the Client / Installer:

The beautiful finished solid wood floor is a product of nature and, for this reason, has its peculiar characteristics. Our hardwood floors are manufactured to industry standards on the market, allowing for deficiencies, not exceeding 5%. These deficiencies may be fabrication or nature of wood. When the floor is requested by the customer, 5% should be added to the square footage for cuts and alignments.

  • The Customer / Installer assumes all responsibility for the final inspection of the product and its quality. Floor inspection must be done prior to installation. Carefully examine the flooring color, varnishing and quality before installing it. If the material is not acceptable, do not install it. Contact the seller immediately.
  • Prior to the installation of any wooden floor, the customer / installer must determine that the installation site and floor are in a condition to receive the product. Construction recommendations and materials should be followed. These instructions recommend that the work and counter floor be clean, dry, rigid and structurally flat.
  • The manufacturer is not liable for any liability caused or caused by deficiencies in the floor or derivatives, in the workplace.

  • Prior to installation, the Customer / Installer must make a final inspection to ensure quality of the fabrication and varnishing. The installer must use “good judgment” for the installation and selection of faulty parts, no matter the cause. If a part is having too many problems such as fabrication or lower grading, the installer should not use this part.
  • The use of dyes, fillers, waterproofing agents or weights for counter-floor correction is acceptable as a normal part of the installation procedures.

 

Storage and Handling:

The finished wooden floor should be stored in the environment that will be installed. Deliver the material in a controlled environment. Use a humidity gauge, measure and document the humidity of both the floor and the hardwood floor. The difference between the floor and the wood can not exceed 4%. Leave the wood acclimatizing in the environment, if necessary, to reach these levels. Store in a dry place, ensuring at least 10cm of space between the cartons in the concrete. The floors should not be delivered until the building is completely closed, with windows and doors in places and until the cement is completely dry. It is recommended 10 days of drying for every 1cm of concrete thickness.

 

Conditions of the counter floor:

  • CLEAN: The floor must be free of wax, paints, oils, adhesives and other materials not indicated for the floor.
  • LEVELING: Sand dregular areas or joints. Waterproof or leveling the lower parts.
  • DRY: Use moisture retardants if necessary.

NOTE: Avoid floors with irregularities. The best performance of the wood floor happens against completely level floors. If your counter floor is with many gaps, it will continue with uneven after installation of the finished wood floor.

 

Tools and Accessories Required:

NOTE: Machinery and Equipment used improperly can cause serious damage. The manufacturer of this wooden floor is not liable for damages caused by improper use of materials or installation tools.

  • PU Glue – PU Waterproofing – PU Remover – Spatula – Hammer – Clean cloths – Glue Mixing Machine – Dust Mask – Moisture Meter – Treadmill – Protective Eyewear

 

STEP BY STEP:

 

STEP 1: Entrance and Wall Preparation:

Cut the underside of the door (if necessary) and stops. Remove any improper material. These items can be replaced after installation.

 

STEP 2: Establish a Starting Point:

Installing finished wood flooring parallel to the longer wall is recommended to have a better visual effect.
Whenever possible, start the installation by the straightest wall, usually a wall that faces the area.

 

STEP 3: Installing the Floor:

Check the installation materials beforehand. Open the PU glue and mix component B into component A. Increase the dosage over time. With your drill, place the mixer and mix the two components together until it turns orange.
Begin installation with a few rows at a time. Use parts of varying sizes for installation, always respecting a minimum spacing of 10cm between floor joints.
The last row should always be cut to the best fit on the wall. Always leave a 1cm spacing for the wall, cut the pieces from the last row (one by one) for the perfect alignment with the wall.

 

STEP 4: Finishing the Installation:

Remove all tapes and clean the floor with the recommended cleaning materials.
Install or reinstall any transition part, such as reducers, T-Moldings, smoothing, skirting. These products are available pre-fabricated to match your flooring.

 

INSTALLERS: ALERT YOUR CUSTOMER ABOUT THE FOLLOWING:

Recognizing that wood floors are highly affected by varying humidity levels, care must be taken to control moisture levels between 35-55%.

NOTE: A final foot inspection must be done by the customer.

WhatsApp chat